How to Fix SPN 3712 – Final Inducement Level (5 MPH Derate)

If your truck is showing SPN 3712, you already know the bad news:

🚨 Your truck is locked in a 5 MPH derate

🚨 You cannot clear it without repairing the root cause

🚨 You MUST use a dealer-level truck scanner to reset inducement

SPN 3712 is one of the most painful codes in the diesel world because it forces Final Inducement Mode, meaning:

❌ No power
❌ No acceleration
❌ No highway driving
❌ Truck barely moves

Let’s break down what SPN 3712 means, how to diagnose it, and how to remove the 5 MPH derate properly.

🚛 What SPN 3712 Means

SPN 3712 = Aftertreatment SCR Final Inducement.

This means:

  • The emissions system experienced a major fault

  • The ECM has locked the truck into a final derate

  • The truck will not recover on its own

  • A repairs + reset procedure is required

This code is common on:

  • Paccar MX-13

  • Cummins ISX / X15

  • Detroit DD13/DD15

  • Volvo/Mack

  • International A26

⚠️ Common Reasons SPN 3712 Appears

SPN 3712 is not the cause — it is the result of other serious emissions failures.

Most common triggers:

✔ Bad NOx Sensors (MOST COMMON)

If inlet/outlet NOx values are incorrect → ECM triggers inducement.

✔ Failed DEF Pump or Low DEF Pressure

Truck cannot dose → SCR fails → inductions.

✔ DEF Quality Below 31%

Contaminated or diluted DEF creates fake NOx readings.

✔ DEF Doser Valve Failure

No dosing → impossible for SCR to reduce NOx → derate.

✔ SCR Efficiency Low (SPN 4364)

Catalyst unable to reduce NOx → final inducement triggered.

✔ DPF High Soot (SPN 3719)

A full DPF forces the system into protection mode.

✔ Wiring Harness Failures

Common on Paccar and Freightliner.

🔧 How to Diagnose SPN 3712 (Step-by-Step Using a Truck Scanner)

You cannot fix SPN 3712 without a truck scanner capable of OEM-level tests.

Here’s the correct procedure:

1️⃣ Read All Codes — Not Just SPN 3712

Look for ROOT CAUSE codes such as:

  • SPN 4364 – SCR Efficiency Low

  • SPN 3216 – NOx Sensor Failure

  • SPN 1231 – DEF Pump or Doser

  • SPN 3719 – DPF Soot Over Limit

  • SPN 520372 – Regens Too Frequent

  • SPN 3251 – DPF Differential Pressure High

These codes tell you what FAILED — SPN 3712 is simply the RESULT.

2️⃣ Test NOx Sensors

In your truck scanner:

✔ Run NOx sensor diagnostics
✔ Compare inlet vs outlet NOx
✔ Ensure response time is normal

Bad NOx sensors = #1 cause of SPN 3712.

3️⃣ Test DEF Pump Pressure

Run a DEF Pump Test:

  • 45–60 PSI normal (varies by brand)

  • Low pressure = internal pump failure

  • Zero pressure = clogged filter or electrical fault

4️⃣ Perform DEF Doser Test

Command dosing event:

✔ Proper spray pattern?
✔ Crystals around injector?
✔ Flow rate low?

If your doser is clogged → SCR cannot function.

5️⃣ Check DEF Quality Using Scanner

Run DEF Quality Test / Percent Concentration.

If below spec:
➡️ Drain tank
➡️ Refill with fresh DEF
➡️ Run DEF quality test again

6️⃣ Perform SCR Efficiency Test

This test determines whether your SCR catalyst is still usable.

If it FAILS → catalyst replacement required.

7️⃣ After Repairs: Clear Final Inducement Lock

Once the cause is fixed, you MUST perform:

✔ Aftertreatment Reset
✔ SCR Inducement Reset
✔ NOx Sensor Reset
✔ DEF System Prime
✔ Parked Regen (MANDATORY)

If you skip these → the 5 MPH derate remains.

🛠 How to Fix SPN 3712 Based on Root Cause

✔ BAD NOx SENSOR

Replace → Run NOx reset → Run SCR efficiency test → Regen

✔ BAD DEF PUMP

Replace → Prime system → Run dosing test → Reset inducement

✔ BAD DEF DOSER

Replace → Run doser test → Perform regen → Clear inducement

✔ CONTAMINATED DEF

Drain/refill → Run DEF quality test → Reset system

✔ SCR EFFICIENCY LOW

Replace catalyst → Perform SCR reset → Regen

✔ DPF OVER-SOOT

Perform forced regen → Reset soot levels → Repair underlying issues

❌ Myths About Fixing SPN 3712

✖ “Can I clear SPN 3712 by disconnecting batteries?”

NO.

✖ “Can I clear SPN 3712 with a cheap scanner?”

NO.

✖ “If I replace parts, will the code go away?”

NOT until resets are performed.

✖ “Can SPN 3712 go away after driving?”

NEVER.

This inducement requires dealer-level diagnostics.

🚀 The Only Reliable Way to Fix SPN 3712

You MUST use a professional truck scanner capable of:

  • SCR resets

  • NOx adaptation resets

  • DEF pump/doser tests

  • Clearing inducement locks

  • Running active regens

  • Reading OEM SPN/FMI data

  • Running SCR efficiency tests

Dealers charge $450–$900+ for this.

You can do it yourself with:

⭐ DieselScanners™ Laptop Diagnostic Kit

The most powerful all-in-one scanner for removing a 5 MPH derate.

Why truckers choose DieselScanners:

✔ Full OEM-level software (Cummins, PACCAR, Detroit, Volvo, Mack, CAT)
✔ Runs forced regens on every brand
✔ Clears inducements & derates
✔ DEF/DPF/SCR testing suite included
✔ Pre-installed & activated laptop
✔ RP1210 adapter support (USB-Link 2/3)
✔ No subscriptions or annual fees

👉 Get your kit at DieselScanners.com
Fix your truck TODAY.

📌 Final Takeaway

SPN 3712 means the ECM has entered FINAL inducement.

It is not the problem — it is the result of a more serious emissions failure.

With a real truck scanner, you can:

  • Identify the root cause

  • Repair the issue

  • Reset the SCR system

  • Remove the 5 MPH derate

  • Get back on the road

Back to blog